Effect of opening location in the wall with corrugated steel plate using the pushover analysis

سال انتشار: 1398
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 484

فایل این مقاله در 11 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_JCEMA-3-2_002

تاریخ نمایه سازی: 2 مهر 1398

چکیده مقاله:

Steel shear walls are far cleaner and are considered more rapid replacements for the concrete shear walls in terms of execution and more reliable in terms of strength and behavior.  Also the system takes advantage of all good characteristics of concentrically braced frames (CBF) like V and X-shaped bracings, etc. and also those of eccentrically braced frames (EBF). They are also efficient in terms of execution and good behavior and in many cases act better. In this research the effect of opening location in the corrugated plate is investigated using the pushover analysis. For the analysis and investigation of the model, use has been made of ABAQUS software and the two available methods for analysis and design of steel shear walls are incorporated. The obtained results showed that the opening in the corrugated steel shear wall causes reduced safety and lateral resistance of the wall, so that where the openings are located at the corners, the effect of reduction is more severe. On this basis, the minimum reduction in stiffness and strength of the steel shear wall with opening is where it is located at the middle of the wall and the worst case is where the opening is located at the corners and close to the columns. 

نویسندگان

Fatemeh Sadat Asadi

Department of civil engineering, Islamic Azad University, Shahre kord Branch, Chaharmahal o bakhtiari, Iran.

Arash Mohammadi Farsani

Department of civil engineering, Islamic Azad University, Shahre kord Branch, Chaharmahal o bakhtiari, Iran.

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Wagner H. Flat sheet metal girders with very thin metal ...
  • Wu N. Friction and Impact Load Response of Ship Shafts ...
  • Nabian M, Nabian MA, Hashemi HN. Torsional Dynamics Response of ...
  • Shelton IV FE, Setser ME, Doll KR, Morgan JR, inventors; ...
  • Shelton IV FE, Setser ME, Weisenburgh IW, inventors; Ethicon Endo ...
  • Driver RG, Kulak GL, Kennedy DL, Elwi AE. Cyclic test ...
  • Dong L, King WP, Raleigh M, Wadley HN. A microfabrication ...
  • Cao Q, Huang J. Experimental study and numerical simulation of ...
  • Myers HC, inventor. Knotless adhesive impregnated sutures and method of ...
  • Roberts TM, Sabouri-Ghomi S. Hysteretic characteristics of unstiffened perforated steel ...
  • Haji J, Kawasaki K, Ishizuka K, Yamada T, inventors; Nippon ...
  • Seo J, Varma AH, Sener K, Ayhan D. Steel-plate composite ...
  • Shamim I, Rogers CA. Numerical evaluation: AISI S400 steel-sheathed CFS ...
  • Farzampour A, Laman JA, Mofid M. Behavior prediction of corrugated ...
  • Premalatha DJ, Vengadeshwari RS, Abhijith B. Study On The Behaviour ...
  • Dou C, Pi YL, Gao W. Shear resistance and post-buckling ...
  • Fu MH, Xu OT, Hu LL, Yu TX. Nonlinear shear ...
  • Chatté G, Comtet J, Niguès A, Bocquet L, Siria A, ...
  • Ashrafi HR, Shahbazian K, Bidmeshki S, Yaghooti S, Beiranvand P. ...
  • Delnavaz A, Hamidnia M. Analytical investigation on shape configuration of ...
  • Fenton GA, Naghibi F, Dundas D, Bathurst RJ, Griffiths DV. ...
  • AISC A. Seismic provisions for structural steel buildings. [View at ...
  • Council BS. NEHRP Recommended Provisions for Seismic Regulations for New ...
  • Zhang TL, Baumjohann W, Nakamura R, Balogh A, Glassmeier KH. ...
  • نمایش کامل مراجع