On the microstructure evolution and mechanical properties of the A390 alloy tubes produced via horizontal centrifugal casting

سال انتشار: 1395
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 738

فایل این مقاله در 10 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICESCON03_202

تاریخ نمایه سازی: 16 شهریور 1395

چکیده مقاله:

Three kinds of functionally graded tube using A390 alloy at various rotation speeds 400,700 and 1000 rpm with thickness of 2cm were produced by horizontal centrifugal casting, and their microstructure and mechanical properties were investigated and compared. Characteristics and distribution of the primary particles were assessed by the optical microscopy (OM), scanning electron microscopy (SEM), and image analyzer software. The hardness and pin-on-disk wear tests along the thickness of samples were performed to investigate the variation in the mechanical properties corresponding to the variation in microstructure. Also, the worn surfaces of the material were examined by scanning electron microscopy (SEM) to study the dominant wear regime. Significant enrichment zones of primary Si particles were observed in the external and internal zone of the casting in the radial2direction of the centrifugal caster, but; in the middle layer, a few reinforcement particles were observed. Furthermore; it is found that, with increasing of the rotation speed, the thickness and volume fraction of particles in the outer layer increase. Corresponding increases in surface micro hardness as well as smaller wear volume loss in the outer layer in comparison with other layer were observed

نویسندگان

Masoud Mohammadi Rahvard

P.hd student of School of Materials Science and Engineering, Iran University of Science and Technology, IUST, Narmak ,Tehran, Iran. Corresponding author

Morteza Tamizifar

Associate professor of School of Materials Science and Engineering, Iran University of Science and Technology, IUST, Tehran, Iran

Seyed Mohammad Ali Boutorabi

professor of School of Materiasl Science and Engineering, Iran University of Science and Technology, IUST, Narmak, Tehran, Iran.

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • T.P.D. Rajan, R.M. Pillai, B.C. Pai. Ch aracterization of centrifugal ...
  • A. Halvaeea, A. Talebi. Effect of process variables on microstructue ...
  • G. Chirita, I. Stefanescu, D. Cruz, D. Soares a, F.S. ...
  • G. Chirita, D. Soares, F.S. Silva. Advantages of the centrifugal ...
  • ZHAI Yan-bo, LIU Chang-ming, W ANG Kai, ZOU Mao-hua, XE ...
  • M.Mohammad rahvard, M.Tamizifar, M .A.Boutorabi, S.Gholami. Characterizato n of the ...
  • Birol. Y, Birol. F. Sliding wear behaviour of thixoformed AISiCuFe ...
  • S.K. Dey, T.A.Perry, A.T. Alpas , Micromechans S of low ...
  • Dwivedi, D.K. Adhesive wears behaviour of cast aluminium-s ilicon alloys. ...
  • _ Sharma. R, Anesh, Dwivedi, D.K. Infuence of silicon (wt.%) ...
  • نمایش کامل مراجع