Theoretical and numerical investigations of effective parameters on edge buckling of channel sections in cold roll forming

سال انتشار: 1390
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,025

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICME12_038

تاریخ نمایه سازی: 25 شهریور 1392

چکیده مقاله:

Excessive longitudinal strain is the main reason of occurring buckling defect at strip edge. A theoretical relation was developed for longitudinal total strain based on the method proposed by Bhattacharyya for roll forming of a channel section. Theoretical results showed that forming angle, flange length, strip thickness and distance from the bend line are the most effective parameters on longitudinal strain and the effect of later is more than the others. The process was simulated three dimensionally by Abaqus software to improve the buckling prediction and to consider yield strength of strip. Simulation results showed that the forming angle, flange length and strip thickness are the most effective parameters on edge buckling respectively. These conclusions were in good agreement with theoretical results. According to the theoretical and numerical results, by increasing the forming angle and flange length and decreasing the strip thickness, buckling probability increases. Low yield strength strips are prone of wavy large amplitude buckling while higher yield strengths may lead to buckles with less wave numbers.

نویسندگان

R Azizi Tafti

Department of Mechanical Engineering, Faculty of Engineering, Tarbiat Modares University, Tehran, Iran

H Moslemi Naeini

Department of Mechanical Engineering, Faculty of Engineering, Tarbiat Modares University, Tehran, Iran

M Salmani Tehrani

Faculty of Mechanical Engineering, Isfahan University of Technology, Isfahan, Iran

M Farzi

Faculty of Mechanical Engineering, Isfahan University of Technology, Isfahan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • D. Bhattacharyya, P. Smith, C. H. Yee, I. F. Collins, ...
  • D. Bhattacharyya, P. Smith, S. K. Thadakamalla, I. F. Collins, ...
  • M. Brunet, S. Mguil, P. Pol, "Modelling of a roll- ...
  • S.M. Panton, S. D. Zhu and J. L. Duncan, "geometric ...
  • S.M. Panton, S. D. Zhu, J. L. Duncan, "Fundamental deformation ...
  • S.M. Panton, J. L. Duncan, S. D. Zhu, "Longitudinal and ...
  • M. Farzin, M Salmani Tehrani, E. Shameli, "Determination of buckling ...
  • MoslemiNaein _ H. Khademizadeh, "Localised edge buckling in cold roll-forming ...
  • M. Salmani Tehrani, H. MoslemiNaeini, P. ...
  • section", J. Materials Pro. Tech., Vol. 44, pp. 184-196, 2006. ...
  • Iternational Conference on Manufacturing Engineering ICME2011, Tehran, Iran ...
  • نمایش کامل مراجع