Numerical simulation of combustion with the aim of obtaining temperature distribution, identifying and eliminating power reduction factors of a gas turbine engine

سال انتشار: 1401
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 88

فایل این مقاله در 12 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_JASTI-15-2_009

تاریخ نمایه سازی: 8 مرداد 1402

چکیده مقاله:

In this research, combustion modeling inside the combustion chamber of a typical turboprop engine has been investigated. The complex geometry of this combustion liner was modeled according to the technical drawings and the turbulent flow and internal combustion were simulated numerically and three-dimensionally. The non-premixed combustion model is used to simulate combustion and the K-ω method is used to simulate turbulent flow. This study investigated how the combustion phenomenon occurs, the internal temperature distribution, the outlet, and the wall of the combustion tube, for which comprehensive three-dimensional data were not previously available. These simulations have identified the weaknesses of the combustion tube and by eliminating these weaknesses, the problem of reducing the efficiency of several gas turbine engines has been solved. Comparison of the results of the present study with a similar numerical analysis showed that the results of this study are more in line with laboratory results. The results of the simulation of combustion pipe defects show that the combustion liner that had a welding line near the outlet had a ۲۵% higher pressure drop than a typical combustion liner and the effective cross-sectional area of ​​the fluid flow was reduced by ۱۱%. The output of a repaired combustion tube is different from a typical type.

نویسندگان

Hamed Arhami

Islamic Azad University, Research Sciences Branch, Tehran

Mohammad Mazidi Sharfabadi

Assistant Professor of Mechanical Engineering, Development and Optimization of Energy Technologies Division, Research Institute of Petroleum Industry (RIPI)

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • D. Bouchard and G. Pucherand and W. D. E. Allan, ...
  • D. A. babu and K. K. Arun and R Anandanarayanan, ...
  • J. J. Gouws, "Combining a one-dimensional empirical and network solver ...
  • K. N. Rizk and V.L. Oechsle and P.T. Ross and ...
  • D. Cerinsk and M. Vujanovie and Z. Petranovic and J. ...
  • S. Maspanov and I. Bogov and A. Smirnov and S. ...
  • L. Jiang and A. Corber, "Assessment of combustor working environments", ...
  • F. W. Skidmore and D. R. Hun and P. N. ...
  • F. W. Skidmore, "Smoke emissions test on series ii and ...
  • F. W. Skidmore and W. H. Schofield, "The variation in ...
  • J. Wang and Z. Li and F. Li, "Stress and ...
  • S. R. D. Guy and W. D. E Allan and ...
  • K. N. Rizk and H. C Mongia, "Three-dimensional combustor performance ...
  • I. I. Enagi and K. A. Al-attab and Z. A. ...
  • نمایش کامل مراجع