Numerical Simulation of Hot Forging Process of KIA Car Brake’s Output Shaft

سال انتشار: 1401
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 139

فایل این مقاله در 10 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_ADMTL-15-1_011

تاریخ نمایه سازی: 9 شهریور 1401

چکیده مقاله:

The present study investigates the production process by closed die forging method of one of the sensitive and safe parts of KIA car brake, which is affected by various mechanical and thermal stresses in its operating conditions; therefore, in the present research, the application of this forming method in the Iranian automotive industry has been discussed. In this study, an attempt was made using finite element analysis in ABAQUS software to determine the maximum force required for forging this part. In addition, the influence of various parameters such as the temperature of the part during the forming process, the coefficient of friction between the part and the die, as well as the strain rate have been investigated. The results indicated that the friction coefficient has a significant effect on the maximum required force, and the maximum values of the load increase with increasing the friction coefficient; but the remarkable result is that the effect of this coefficient is negligible from a value onwards. This point is consistent with the observations in practice. Besides, a strong dependence of the results on the loading speed was observed, and the required force has increased with increasing loading speed for reasons such as the strain hardening phenomenon. Also, the force required for forging has decreased with increasing the temperature, which is due to reduced material strength. This reduction from ۹۰۰°C to ۱۰۰۰°C is less than ۲%, while it is approximately ۴۰% from ۱۰۰۰°C to ۱۱۰۰°C, which is consistent with the experimental reports.

نویسندگان

saeid Hashemian

Faculty of Mechanical Engineering, Urmia University of Technology, Urmia, Iran

Peyman Mashhadi Keshtiban

Faculty of Mechanical Engineering, Urmia University of Technology, Urmia, Iran

Abuzar Es&#۰۳۹;haghi Oskui

Department of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Grass, H., Krempaszky, C., and Werner, E., ۳-D Fem-Simulation of ...
  • Vazquez, V., Altan, T., Die Design for Flashless Forging of ...
  • Lv, C., Zhang, L.,Mu, Z., Tai, Q., and Zheng, Q., ...
  • Alimirzaloo, V., Biglari, F. R., Sadeghi, M. H., Keshtiban, P. ...
  • Taghavi, V., Alimirzaloo, V., Solimanpur, M., Mashhadi Keshtiban, P., and ...
  • Yuli, L., Kun, D., Mei, Z., He, Y., and Fuwei, ...
  • Zhang, Y., Shan, D., and Xu, F., Flow Lines Control ...
  • Ou, H., Wang, P., Lu, B., and Long, H., Finite ...
  • Sadeghi, M., Khosravi, A., Parametric Design, Mold Design and Manufacture ...
  • Parseh, Y., Sadeghi, M., Numerical Simulation and Physical Modeling to ...
  • Yazdi, M. S., Bagheri, G. S., and Tahmasebi, M., Finite ...
  • Narayan, S., Rajeshkannan, A., Hardness, Tensile and Impact Behaviour of ...
  • Sweet, G., Williams, B., Taylor, A., Hexemer, R., Donaldson, I., ...
  • Dareini, M., Jabbari, A., and Sedighi, M., Effect of Nano-Sized ...
  • Choi, Y. J., Lee, S. K., Lee, I. K., Hwang, ...
  • Zhuang, W., Hua, L., Wang, X., Liu, Y., Dong, L., ...
  • Dieter, G. E., Bacon, D. J., Mechanical Metallurgy, ed., McGraw-Hill ...
  • Valberg, H. S., Applied Metal Forming: Including Fem Analysis, ed., ...
  • Mashhadi Keshtiban, P., Taher, A., and Mashhadi Keshtiban, M., Practical ...
  • نمایش کامل مراجع