Optimization of thermal curing cycle for a large epoxy model

سال انتشار: 1398
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 380

فایل این مقاله در 7 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_JCAM-50-2_009

تاریخ نمایه سازی: 31 تیر 1399

چکیده مقاله:

Heat generation in an exothermic reaction during the curing process and low thermal conductivity of the epoxy resin produces high peak temperature and temperature gradients which result in internal and residual stresses, especially in large epoxy samples. In this paper, an optimization algorithm was developed and applied to predict the thermal cure cycle to minimize the temperature peak and thermal gradients within the material of an industrial epoxy model during the curing process. An inverse analysis was used to obtain the new coefficients of Kamal’s equations for the model. To validate and verify the developed model, temperature profiles for several points of the material in the model were obtained by numerical simulation and compared with the previously experimentally measured data. With validated curing simulation, the mentioned inverse analysis and optimization algorithm were utilized to find the thermal curing cycle with several isothermal holds and temperature ramps. The new objective reference was proposed for the first time and used to optimize the cure cycle, which subsequently produced the same temperature profiles for all points. The results showed that the obtained optimized thermal curing cycle was most effective to decrease the peak temperature as well as temperature gradients of the material.

نویسندگان

Mahmood Yaghoubi

school of mechanical engineering, Shiraz university, Shiraz, Iran

Zafar Namazian

school of mechanical engineering, Shiraz university, Shiraz, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • C. G. Zelibe, O. Adewumi, A. Onitiri, 2019, Numerical investigation ...
  • I. Jones, Y. Zhou, S. Jeelani, J. Mabry, 2008, Effect ...
  • P. Ghabezi, M. Farahani, 2016, Composite adhesive-bonded joint reinforcement by ...
  • J. Duan, C. Kim, P. Jiang, 2009, On-line monitoring of ...
  • Y. A. Chekanov, V. Korotkov, B. Rozenberg, E. Dhzavadyan, L. ...
  • Predicting Low Cycle Fatigue Life through Simulation of Crack in Cover Plate Welded Beam to Column Connections [مقاله ژورنالی]
  • P. Wang, H. Lei, X. Zhu, H. Chen, D. Fang, ...
  • Y. He, Q. Chen, S. Yang, C. Lu, M. Feng, ...
  • C. Leistner, S. Hartmann, J. Wittrock, K. Bode, 2018, Shrinkage ...
  • J. Zhang, 2009, Effect of cure cycle on curing process ...
  • S. Pusatcioglu, J. Hassler, A. Fricke, H. McGee Jr, 1980, ...
  • M. Hojjati, S. Hoa, 1994, Curing simulation of thick thermosetting ...
  • A. K. Kulshreshtha, C. Vasile, 2002, Neuroclave: The Intelligent Autoclave, ...
  • C. Warnock, T. T. Briggs, Cure Cycle Development and Qualification ...
  • R. Sekula, P. Saj, T. Nowak, K. Kaczmarek, K. Forsman, ...
  • K. Kasza, L. Matysiak, L. Malinowski, 2010, Method to describe ...
  • E. Ruiz, F. Trochu, 2005, Numerical analysis of cure temperature ...
  • Ł. Matysiak, 2014, Experimental analysis and inverse approach in numerical ...
  • M. N. Ozisik, H. R. B. Orlande, 2000, Inverse Heat ...
  • نمایش کامل مراجع