Interface Characterization of Al/Cu/Al Tri-layer Composites after Explosive cladding and Rolling Process

سال انتشار: 1393
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 750

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

COMPOSIT04_169

تاریخ نمایه سازی: 22 مهر 1394

چکیده مقاله:

In the present study, the fabrication of tri-layer composites by explosive welding and subsequent rolling has been investigated. The effect of cladding/deformation variables on the integrity, the soundness and microstructural properties were evaluated using optical microscopy as well as the micro-hardness testing. It was observed that, when the explosive ratio was increased smooth bonding interface transformed to a wavy interface accompanied by the formation of intermetallic components. The hardness of bonding interface of plates was increased because of deformation that was originating from the impact effect. Interest was directed towards the surface topography, metallurgical changes of interface zone and characterization of defects could affect the properties of the composite products. In addition, the difference in the plastic strain experienced by each material increases with increase in the total plastic strain and volume ratio that may result in de cohesion, fracture or other heterogeneity.

نویسندگان

M.M Hosseini Athar

M.S. student, Department of Metallurgy and Materials Engineering, Faculty of Engineering, University of Kashan, Kashan, Iran

B Tolaminejad

Assistant professor, Department of Metallurgy and Materials Engineering, Faculty of Engineering, University of Kashan, Kashan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Characteristic damage phenomena of explosive cladding, [1] Milenin, A.A., Berski, ...
  • Were observed for the metals and the c ladding/rolling [2] ...
  • processing parameters to fabricate sound laminated [4] Mamalis, A.G., Vaxevanidis, ...
  • The joint interface _ flat in case of using lower ...
  • higher explosive ratio. It is also observed intermetallic [6] B. ...
  • Alcaraz, J.L, Gil-Sevillano, J, M artinez -Esnaola, J. M., Journal ...
  • hardness for aluminum _ more than copper. This increase [8] ...
  • flattening of the waves and the entrapping regions adjacent to ...
  • intermetallic fragmentation and separation suppressed the end [10]Livne, Z., Munitz, ...
  • There exists an optimal interfacial pressre beyond which [11]Gulbin, V.N, ...
  • uniformities and below which there is greater probability for [12]Bahrani, ...
  • Increasing volume of the hard core layer enhance the [13]Szecket, ...
  • additional hardening in clad and a reduction of the strength ...
  • Mamalis, A.G., Vaxevanidis, N.M., Szalay A., Prohaszka, J., Journal of ...
  • Afonja, A. A., Sansome, D.H., Journal of Mechanical Working Technology ...
  • Rydz, D., Dyja, H., Krakowiak, M., Journal of Materials Processing ...
  • Osakada, K., Limb, M., Mellor, P.B., international journal ...
  • _ _ _ _ A (Physical Metallurgy and Materials Science) ...
  • Nowicke, F., Zavaliangos, A., Rogers, H.C., International Journal of Mechanical ...
  • Tolaminejad, B., Arabi, H., Iranian Journa of Science & Technology, ...
  • نمایش کامل مراجع