VISUALIZATION ANALYSIS OF INSTANT FLOW RATE IN INJECTION MOLDING PROCESS

سال انتشار: 1386
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,488

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ISME15_545

تاریخ نمایه سازی: 8 فروردین 1386

چکیده مقاله:

This paper presents a research work on visualization of the flow front advancement during filling stage of the plastic injection molding process. A visual mold was designed and manufactured to monitor the flow advancement. Observations were carried out for two cavity designs: i) a simple rectangular plate (non-constrained plate) and ii) a rectangular plate with an obstacle pin (constrained plate). The flow advancement was recorded using a high speed camera. The recorded frames of the advancing flow front were used to measure the instant flow rate. The implemented setup could clearly show the flow behavior from which the instant flow rate could be extracted. Results show a relatively high dependency of the flow rate on the mold geometry.

نویسندگان

Saeed Fathi

Department of Mechanical Engineering Tarbiat Modares University, Tehran, Iran

Amir Hossein Behravesh

Department of Mechanical Engineering Tarbiat Modares University, Tehran, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Bogaerds, A.C.B., Hulsen, M.A., Peters, G.W.M., Baaijens, F.P.T., Journal of ...
  • Lacrampe, M. F., Pabiot, J., Journal of Injection Molding Technology, ...
  • Nguyen Chung T., Mennig G., Rheology Acta, 2001, Vol. 40, ...
  • Kazmer, D.O., Fan, B., Nageri, R., "On-line Flow Rate and ...
  • Ravabdeh, I.B., Petersen, P.F., Journal of Injection Molding Technology, 3 ...
  • Yokoi, H., Hayashi, T., Toda, K., Morita, N., Proceedings of ...
  • Yokoi, H., Masuda, N., Mitsuhata, H., Journal of Materials Processing ...
  • Dowling D.R., Bress T.J., "Visualization of Injection Molding", Proceedings of ...
  • نمایش کامل مراجع