Evaluation of Bipolar Plate Bonding Adhesives with the Aim of Increasing PEM Fuel Cell Power Density

سال انتشار: 1405
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 27

فایل این مقاله در 12 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_IJHFC-13-3_007

تاریخ نمایه سازی: 22 آبان 1405

چکیده مقاله:

One of the strategies to increase the power density of fuel cells is reducing the thickness of composite bipolar plates. However, considering the brittle nature of these plates, a reduction in thickness may result in fracture under applied loading. The use of adhesives for sealing, instead of elastomeric gaskets on the cooling side of bipolar plates, enables bonding of the anode and cathode plates together, thereby improving mechanical strength. Consequently, applying adhesives can significantly enhance the power density of the fuel cell. In this study, the performance of structural (epoxy–phenolic) and non-structural (fluorinated vinyl ester) adhesives was evaluated under fuel cell operating conditions. Essential properties such as adhesion strength, effective sealing, ease of preparation and application, thermal stability, and chemical resistance in the acidic fuel cell environment were investigated. The results revealed that epoxy–phenolic adhesives, due to their high shear strength, negligible weight loss, dense cross-linked structure, and the presence of phenolic rings, are more suitable for structural applications. In contrast, fluorinated vinyl ester adhesives exhibited zero weight loss under the same conditions and excellent chemical resistance, but lower mechanical strength. Specifically, EP-Ph۱۰ exhibited a lap shear strength of ۱۰.۲ MPa, while VES-PFO۵ showed ۸.۴ MPa. Chemical resistance tests indicated <۰.۵% weight loss for EP-P, EP-Ph۵, EP-Ph۱۰, VES, and VES-PFO۵, whereas EP-D showed approximately ۲.۰% weight loss in H۲SO۴ and ∼۳.۰% in HF after ۳۰ days.

نویسندگان

- -

Northern Research Center for Science and Technology, Malek-Ashtar University of Technology, Iran

- -

Northern Research Center for Science and Technology, Malek-Ashtar University of Technology, Iran

- -

Department of Mechanical Engineering, Technical and Vocational University (TVU), Tehran, Iran

- -

Department of Mechanical Engineering, Technical and Vocational University (TVU), Tehran, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Kim M, Yu HN, Lim JW. Bipolar plates made of ...
  • Kim M. Development of the anode bipolar plate/membrane assembly unit ...
  • Rzeczkowski P, Krause B, Pötschke P. Characterization of highly filled ...
  • Bhlapibul S, Pruksathorn K. Preparation of graphite composite bipolar plate ...
  • Müller A, Kauranen P, Von Ganski A, Hell B. Injection ...
  • Jeong KI, Oh J, Song SA, Lee D, Kim SS. ...
  • Kakati BK, Sathiyamoorthy D, Verma A. Electrochemical and mechanical behavior ...
  • Jie Z, Yan-wen Z, Jun HE. Influence of graphite particle ...
  • Ishai O, Rosenthal H, Sela N, Drukker E. Effect of ...
  • Hsiao KT, Alms J, Advani SG. Use of epoxy/multiwalled carbon ...
  • Stammen E, Brokamp S, Weber M, Heinzel A, Dilger K. ...
  • Wang JG, Guo QG, Liu L, Song JR. Study on ...
  • Wang J, Jiang N, Guo Q, Liu L, Song J. ...
  • Rzeczkowski P, Lucia M, Müller A, Facklam M, Cohnen A, ...
  • Blunk RH, Abd Elhamid MH, Lisi DJ, Mikhail YM, Budinski ...
  • Farrington S. Assembling bipolar plates for fuel cells using microencapsulated ...
  • Sekine S. Adhesive material for fuel cell and fuel cell; ...
  • نمایش کامل مراجع