CFD Simulation of Supersonic Combustion and Mixing with Flushwall and Ramp Injection Effects for Scramjet Propulsion

سال انتشار: 1405
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 27

فایل این مقاله در 28 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_JCAM-57-4_002

تاریخ نمایه سازی: 22 آبان 1405

چکیده مقاله:

Scramjet technology promises to reduce the cost of space access systems by eliminating rocket staging designs to reach orbit which are costly and single use. To date, several Scramjet engine testbeds have been capable of igniting and producing thrust in flight conditions, but these tests are not common. Scramjet propulsion systems are faced with complex flow-physics behaviours that moderate their technological development. The insufficient knowledge available on restricted sonic airflow conditions requires computational methods for accurate predictions prior to flight testing. This article therefore deploys ANSYS FLUENT Computational Fluid Dynamic (CFD) software to analyse supersonic flow characteristics in current scramjet combustor designs. The scope of flow passage optimisation in Scramjets lies primarily with the selected fuel injection methods and in this regard both flush wall (۳۰ degrees and ۸۰ degrees inclination) and ramp injector (۱۲ degrees and ۱۸ degrees inclination) designs are simulated here. Reynolds Averaged Navier Stokes (RANS) computations are described to provide numerical results for high velocity, recirculating flows and static pressure, temperature, velocity, density and hydrogen/water/oxygen mass fraction contours are presented. Detailed mesh designs are included and a grid independence study. The material properties of air and the mixture (hydrogen-air) feature ideal-gas density and Sutherland’s viscosity for heat transfer properties to accurately simulate compressibility effects. A two equation, realizable k-epsilon turbulence model is employed with standard wall treatment, to encompass superior simulated rotational spreading behaviour of the flow. The Turbulent Kinetic Energy (TKE), Energy and Wall Prandtl numbers are set as ۱, ۰.۸۵, and ۰.۸۵ respectively. To model the mixing, heat transfer, and combustion with the realizable k-epsilon model, a volumetric, hydrogen-air mixture Species-Transport model with Eddy-Dissipation turbulence-chemistry interactions is incorporated with turbulent Schmidt number of ۰.۷ and a Turbulent Dissipation Rate (TDR) of ۱.۲. Two distinct fuel injection methods are presented in this study- the transverse flush wall injection and the ramp method. The hydrogen fuel is injected through a port with a ۲mm cross-sectional area. The ramp injection method is an intrusive fuel injection method which trades thrust potential in the form of pressure losses for good mixing characteristics. The strength of the oblique shockwave that forms is entirely dependent on the inclination of ramp, with greater inclination resulting in a stronger shockwave. The presence of the oblique shockwave further increases the mixing downstream of fuel injection due to the interaction of reflected shockwaves with the fuel and air mixing layer. Similar to the flush wall injectors, both ramp designs feature fuel injection ports of ۲mm diameter, where the opening of the injector port is ۲mm below the upper trailing edge of the ramp geometry. The ۱۸˚ ramp, due to its high profile, generates strong oblique shockwave formation and enhanced downstream mixing due to increased pressure and temperature due the reflection of the intense oblique shock. The ۸۰˚ flush wall injector features the same general dimensions as the first case at ۳۰˚ inclination but introduces the hydrogen fuel near perpendicular to the airflow.

نویسندگان

- -

MSc Advanced Mechanical Engineering Program, SEE Building, Salford University, M۵ ۴WT, UK

- -

Multi-Physical Engineering Sciences Group, Mechanical Engineering Department, Corrosion and Coatings Lab, Room ۳-۰۸, SEE Building, University of Salford, Manchester, M۵۴WT, UK

- -

Engineering Mechanics Research, Israfil House, Dickenson Rd., Manchester, M۱۳, UK

- -

Multi-Physical Engineering Sciences Group, Mechanical Engineering Department, Corrosion and Coatings Lab, Room ۳-۰۸, SEE Building, University of Salford, Manchester, M۵۴WT, UK.

- -

Department of Physics, College of Science, Korea University, ۱۴۵ Anam-ro, Seongbuk-gu, Seoul ۰۲۸۴۱, Republic of Korea

- -

Multi-Physical Engineering Sciences Group, Mechanical Engineering Department, Corrosion and Coatings Lab, Room ۳-۰۸, SEE Building, University of Salford, Manchester, M۵۴WT, UK

- -

Multi-Physical Engineering Sciences Group, Mechanical Engineering Department, Corrosion and Coatings Lab, Room ۳-۰۸, SEE Building, University of Salford, Manchester, M۵۴WT, UK

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :