Prediction of damage by dynamic FLD criterion in high velocity sheet metal forming and experimental results

سال انتشار: 1392
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,063

فایل این مقاله در 15 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

WMECH02_026

تاریخ نمایه سازی: 21 تیر 1393

چکیده مقاله:

In This paper dynamic forming limit diagram has been investigated as fracture criteria for ST13 steel. In fact, effect of various strain rates has been studied. This fracture criterion is based on the Marciniak-Kuczynski (M-K) theory and the Solution of equations has been obtained by applying the Newton-Raphson method. After solution three forming limit diagrams have been created: independent strain rate, dependent strain rate and dynamic forming limit diagram. Dynamic damage criteria investigates forming limit diagram in every strain rate. It is observed that the forming limit is increased by increasing the strain rate, Also for considering the anisotropic and the elastic-plastic behavior of material, the Hill 1948 yield criterion and the Swift hardening rule are used respectively. Also this paper is concerned with the uniaxial tensile properties and formability of sheet metal in relation to the strain rate effects. In order to verification of the results several experiments have been done with a Drop Hammer that is a high speed impact machine. For comparison between quasi static and dynamic damage criterions, all of the stages of experiment were simulated in finite element software Abaqus and results are compared together.

نویسندگان

Ali basti

Assistant Professor

Mohammad zaeimi

PhD student Department of Mechanical Engineering, Guilan University, Guilan Impact laboratory, school mechanical of engineering, Guilan University, ۴۱۹۹۸-۴۳۶۵۳, Guilan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • S. P. Keeler, Circular Grid System: A valuabe Ai for ...
  • G. M. Goodwin, Application of Strain Analysis to Sheet Metal ...
  • Z. Marciniak, K. Kuczynski, Limit Strains in the Proces of ...
  • Z. Marciniak, K. Kuczynski, T. Pokora, Influence of the Plastic ...
  • A. Barata da Rocha, F. Barlat, J.M. Jalinear, Prediction of ...
  • R. Sowerby, J. L. Duncant, Failure in Sheet Metal in ...
  • M. M. Moshksar, S. Mansorzadeh, Determination of the forming limit ...
  • Haroldo Beri Campos, Marelina Carmen Butuc, Jose Joaquim Gracio, Joao ...
  • S. Ahmadi, A. R. Eivani, A. Akbarzadeh, Experimental and analytical ...
  • S. B. Kim, H. Huh, H. H. Bok, M. B. ...
  • M. Jie, C. H. Cheng, L. C. Chan, C. L. ...
  • A. Assempour, M. Ganjiani, Imp lementation of a robust algorithm ...
  • Mala Seth Dehra, High Velicity Formability and Factors Affecting it, ...
  • نمایش کامل مراجع