The Effect of Tungsten on Microstructure and Mechanical Properties of Sintered Tantalum by Hot Pressing in a Vacuum

سال انتشار: 1404
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 96

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_IJMF-12-1_003

تاریخ نمایه سازی: 20 اردیبهشت 1404

چکیده مقاله:

In this study, the effect of tungsten addition on the microstructure and mechanical properties of tantalum using hot pressing-sintering is investigated. Pure tantalum and tungsten powders were used to produce Ta-W alloys with varying tungsten content, including pure Ta, Ta-۲.۵ wt.% W, Ta-۵ wt.% W, and Ta-۷.۵ wt.% W. The morphology of the powders was examined by scanning electron microscopy. Consolidation was performed via hot pressing-sintering at ۱۶۰۰ °C under vacuum conditions. Density was measured using the Archimedes method, and the microstructure was analyzed by optical microscopy. Hardness measurements were conducted on the sintered samples, and their deformation behavior was evaluated using uniaxial compression test at room temperature. The results indicated that the relative density of pure Ta is ۹۷.۵%, which decreases to ۹۲.۵% with the addition of ۷.۵ wt.% tungsten. With increasing tungsten content, the average grain size decreased while the porosity percentage increased. The properties of Ta-W alloys are influenced by three main characteristics: tungsten content, porosity percentage, and the grain size. The addition of tungsten to tantalum increased most mechanical properties, including hardness, compressive strength, yield strength, toughness, and resilience modulus, although ductility decreased by ۱۰%.

نویسندگان

F. najafzadegan

Science and Research Branch, Islamic Azad University, Tehran, Iran

A khodabandeh

Science and Research Branch, Islamic Azad University, Tehran, Iran

H. Youzbashizadeh

Department of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran

M. Tamizifar

School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Narmak, Tehran ۱۶۸۴۶-۱۳۱۱۴, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Caron, R. N., Staley, J. T. (۱۹۹۷). Effects of composition, ...
  • Burns, R. H., Fang, J. C., Kumar, P. (۱۹۹۶). Evolution ...
  • Chou, P. C., & Crudza, M. E. (۱۹۹۲). The effects ...
  • Flater, P., House, J., O'Brien, J., & Hosford, W. F. ...
  • Cardonne, S. M., Kumar, P., Muchaluk, C. A., Schwartz, H. ...
  • Chen, C., Wang, S., Jia, Y. L., Wang, M. P., ...
  • Muller, J. F., & Dinh, P. M. (۱۹۹۴). Evaluation of ...
  • Waters, C., Salih, M., & Ajinola, S. (۲۰۱۵). Porosity comparative ...
  • Da Silva, V. D. (۲۰۰۵). Mechanics and strength of materials. ...
  • نمایش کامل مراجع