Optimizing Heat Transfer in Microchannel Heat Sinks: A Numerical Investigation with Nanofluids and Modified Geometries
محل انتشار: ماهنامه بین المللی مهندسی، دوره: 37، شماره: 5
سال انتشار: 1403
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 118
فایل این مقاله در 16 صفحه با فرمت PDF قابل دریافت می باشد
- صدور گواهی نمایه سازی
- من نویسنده این مقاله هستم
استخراج به نرم افزارهای پژوهشی:
شناسه ملی سند علمی:
JR_IJE-37-5_005
تاریخ نمایه سازی: 24 اسفند 1402
چکیده مقاله:
The utilization of microchannel heat sinks stands as one of the most reliable solutions for dissipating heat generated in electronic chips. In this numerical study, a fractal microchannel heat sink employing three nanofluids Cu-water, Al۲O۳-water, and TiO۲-water with variable volume fractions of ۲ and ۴ percent as the cooling fluid within the microchannels was investigated. The fluid flow inside the microchannels was analyzed from both hydrodynamic and thermal perspectives. The parameters such as pump power, Nusselt number, and performance evaluation criterion (PEC) were studied. Results demonstrate that heat transfer increases with an increase in the flow rate and volume fraction of nanoparticles. The maximum temperature reduction for the Cu-water nanofluid at an inlet flow rate of ۲۰۰ ml/min and a volume fraction of ۴% is ۲.۴۱%, the highest among the investigated nanofluids. However, this nanofluid also exhibits the highest pressure drop, reaching ۲۵% at a ۴% volume fraction. The PEC number analysis reveals an overall performance increase for all three microchannels. The Cu-water nanofluid exhibits the best comprehensive performance, providing an ۸% overall enhancement, followed by Al۲O۳-water and TiO۲-water nanofluids, which increase the system performance by ۵% and ۴%, respectively. Furthermore, the study introduced fins and cavities to the microchannel branches to enhance heat transfer and overall performance. Results indicate an increase in heat transfer for both modified geometries. The microchannel with fins exhibits a ۳.۵% lower maximum temperature compared to the original geometry at an inlet flow rate of ۲۰۰ ml/min, while the microchannel with cavities showed a ۱% reduction. However, the microchannel with fins experiences a ۴۰۰% higher pressure drop than the initial geometry, while the microchannel with cavities has a ۴% increase. PEC number analysis demonstrated that the microchannel with cavities improves system performance by ۸%, whereas the microchannel with fins reduced system performance by ۴%.
کلیدواژه ها:
نویسندگان
F. Nasiri Khamesloo
Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran
D. Domiri Ganji
Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran
مراجع و منابع این مقاله:
لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :