Influence of Mould Thickness on Microstructure, Hardness and Wear of AL-Cu Cast Alloys

سال انتشار: 1400
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 312

فایل این مقاله در 7 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_IJE-34-8_023

تاریخ نمایه سازی: 12 مرداد 1400

چکیده مقاله:

Aluminium – copper alloys have a wide range of industrial applications especially in military vehicles, rocket fins and aerospace. Solidification plays a vital role in controlling, the mechanical and tribological properties, and influencing the microstructure of metallic alloys in general and aluminium alloys in particular. Therefore, the researchers have made many efforts to figure out the solidification behaviour of Al-Cu alloys. Despite all these endeavors, however, the behavior is not yet fully understood. This research aims to investigate the effect of cooling rate on the microstructure, mechanical and tribological properties of aluminium-copper cast alloys (Al-Cu alloys) under dry sliding conditions. Four cooling rates were achieved by using four various steel moulds made of different thicknesses and one of them was surrounded with green sand, to get a lower cooling rate, with the same respective mould hole geometries. The microstructure results showed that the grain size increases with decreasing the cooling rate. While the hardness increased largely due to the refinement of the microstructure. Finally, it was concluded that the wear rate increases with decreasing the cooling rate, and this due to the reduction in hardness.

نویسندگان

N. Soliman

Mechanical Technical Department, Technical Institute of Kirkuk, Northern Technical University, Iraq

D. Ramadan

Mechanical and Energy Engineering Techniques Department, Erbil Technical Engineering College, Erbil Polytechnic University, Erbil, Kurdistan Region, Iraq

J. Yagoob

Technical College of Kirkuk, Northern Technical University, Iraq

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Wierzbinska, M., Sieniawski, J. "Microstructural Changes of Al-Cu Alloys After ...
  • doi: ۱۰.۵۷۷۲/۲۲۱۹۵ ...
  • Rana, R.S., Purohit, R., Das, S. "Reviews on the Influences ...
  • Sahoo, A.K., Behera, A., Behera, S., Senapati, S. "Development of ...
  • Amoorezaei, M., Gurevich, S., Provatas, N. "Spacing characterization in Al-Cu ...
  • https://doi.org/۱۰.۱۰۱۶/j.actamat.۲۰۱۰.۰۷.۰۲۹۵. Li, M., Wang, H., Wei, Z., Zhu, Z. "Effect ...
  • doi:۱۶۷۲-۶۴۲۱(۲۰۱۰)۰۱-۰۳۷-۰۶۶. Aryshenskii, E., Hirsch, J., Yashin, V., Konovalov, S., Chitnaeva, ...
  • https://doi.org/۱۰.۳۳۹۰/met۱۰۰۹۱۱۶۸۹. Chausov, M., Pylypenko, A., Berezin, V., Volyanska, K., Maruschak, ...
  • Talamantes-Silva, M.A., Rodríguez, A., Talamantes-Silva, J., Valtierra, S., Colás, R. ...
  • https://doi.org/۱۰.۱۰۱۶/j.matchar.۲۰۰۸.۰۱.۰۰۵۱۶. Li, J., Bourgeois, L., Tsalanidis, A., Weyland, M., Medhekar, ...
  • Higgins, R. Engineering Metallurgy: Applied Physical Metallurgy. Printed in Great ...
  • Jabur, A.S. "Preparation and Characterization of Cast Aluminum Matrix-SiC Particulate ...
  • نمایش کامل مراجع