The Effect of Ridges to Improve Ductility and Reduce Deformation Energy in Deep-Drawing Process

سال انتشار: 1399
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 200

فایل این مقاله در 12 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_IJMF-7-2_005

تاریخ نمایه سازی: 18 فروردین 1400

چکیده مقاله:

In this research, two new methods that improve the drawing depth of deep-drawing processes have been introduced. In the first technique, by creating ridges on the punch surface, the stress concentration is decreased on the blank near the punch edge, in turn increasing the drawing depth. The second method is based on the principle of reducing resistant force in the flange area between the die, the blank-holder and the blank that can decrease the required forming energy. By using the ridges on the flange surfaces of die and blank-holder, the contact surface is reduced, which in turn can decrease the force required for blank forming. The simulation results of finite elements are compared to the experimental data. It is found that the ridged punch may delay the blank rupture and significantly raise the drawability.

نویسندگان

Sadra Ranjbaran

Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran

Mehran Kadkhodayan

Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • [1] A.S. Wifi, "An incremental complete solution of the stretch-forming ...
  • [2] K. Manabe, H. Koyama, S. Yoshihara, T. Yagami, "Development ...
  • [3] M.T. Browne, M.T. Hillery, "Optimising the variables when deep-drawing ...
  • [4] S. Kataoka, M. Murakawa, T. Aizawa, H. Ike, "Tribology ...
  • [5] S. Yoshihara, K. Manabe, H. Nishimurab, "Effect of blank-holder ...
  • [6] M. Gavas, M. Izciler, "Effect of blank-holder gap on ...
  • [7] S.H. Zhang, K. Zhang, Y.C. Xu, Z.T. Wang, Y. ...
  • [8] G. Palumbo, D. Sorgente, L. Tricarico, S.H. Zhang, W.T. ...
  • [9] H.I. Demirci, M. Yasar, K. Demiray, M. Karali, "The ...
  • [10] C. Özek, M. Bal, "The effect of die/blank-holder and ...
  • [11] S. Raju, G. Ganesan, R. Karthikeyan, "Influence of variables ...
  • [12] M. Kadkhodayan, F. Moayyedian, "Analytical elastic-plastic study on flange ...
  • [13] S. Bagherzadeh, B. Mollaei-Dariani, K. Malekzadeh, "Theoretical study on ...
  • [14] M. Bao, W. Min, W.U. Xiang-dong, Z. Ying-ke, "Development ...
  • [15] F. Gong, B. Guo, C. Wang, D. Shan, "Micro ...
  • [16] S.A. Ossia, B. Soltani, "Finite element simulation of the ...
  • [17] Y.M. Huang, Y.S. Wu, J.M. Huang, "The influence of ...
  • [18] H. Zein, M. El sherbiny, M. Abd-Rabou, M. El ...
  • [19] A.C. Reddy, "Parametric optimization of warm deep-drawing process of ...
  • [20] A.C. Reddy, "Formability of superplastic deep-drawing process with moving ...
  • [21] S. Katayama, S. Natsume, K. Yamazaki, J. Han, H. ...
  • [22] W. Ma, B. Wang, J. Zhou, M. Huang, "Influence ...
  • [23] W.K. Jawad, A.S. Jaafar, "The influence of punch profile ...
  • [24] B.T. Lin, K.M. Huang, C.C. Kuo, W.T. Wang, "Improvement ...
  • [25] S. Kataoka, M. Murakawab, T. Aizawac,  H. Iked, "Tribology ...
  • [26] M. Geiger, "Towards clean forming technologies," CIRP Annals-Manufacturing Technology ...
  • [27] M. Arentoft, N. Bay, P.T. Tang, J.D. Jensen, "A ...
  • [28] A. Brosius, A. Mousavi, "Lubricant free deep-drawing process by ...
  • نمایش کامل مراجع