F.E. Stability Analysis of Wye-branch Steel Lining

سال انتشار: 1382
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 2,074

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICCE06_419_5085776739

تاریخ نمایه سازی: 25 مهر 1384

چکیده مقاله:

Power stations with high heads are nowadays, almost without exception, designed so as to have one pipeline, or only very few pipelines,supplying the water to the generating station. The penstock is connected to a distributor, which has the task of distributing the flow,with the lowest possible losses of energy, to the individual turbines. The function and location of this section of the plant make it understandable that its safety is regarded as a matter of outstanding importance. Careful selection of materials, followed by continuous and extremely meticulous inspections of work-pieces and production processes, enable the manufacturer to rule out unwarrantable risks as regards materials. Furthermore, wellsubstantiated method of computation and experimental stress investigations make it possible to control stresses occurring in the complicated bifurcations. Thus adequate safety and economical design of the construction are ensured by suitable matching of stress levels to the properties of the materials used.Generally, external pressures can occur either during the tunnel grouting operation or on tunnel dewatering after a prolonged period of use, and very often it is the external,rather than the internal pressure, that determines thickness of the steel liner. In cases where a substantial increase in liner thickness would be required to prevent buckling due to external pressure, it may be more economical to provide external stiffener ribs. For short steel-lined pressure tunnels, drainage arrangements to relieve the external pressure load on tunnel dewatering can be considered. However, for long pressure tunnels, it may not be possible to clean the drains periodically and drainage facilities cannot be relied upon In this paper, a non-symmetry wye-branch is partitioned geometrically into seven imperfect cones. The buckling mode of each section and critical external pressure are calculated upon the effects of geometrical non-linearity in FE framework. This framework can be employed to predict buckling load of such multi-sections thin walled structures against external pressure

نویسندگان

S.A.Sadrnejad

Associate Prof., Civil Engineering Dept., K.N.Toosi University of Technology, Teheran, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • C.E.C.T. Standard, _ ' Rec ommendation for The Design, Manufacture ...
  • Blaisdell, F.W., and Manson, P.W., Energy loss at pipe junctions, ...
  • Ito, H., and Imai, K., 4Pressure losses in vaned elbows ...
  • Ito, H., and Imai, K., *Energy losses at 90 pipe ...
  • Jamison, D.K., and Villemonte, J.R., ،Junction losses in laminar and ...
  • DIN Standard 17102, ،، Weldable normalized fine grain structural steels?, ...
  • American Water Works Association Journal, Vol.47, no.VI, June 1955. ...
  • نمایش کامل مراجع