Investigation of the Microstructure and Wear Behavior of In-Situ High Chromium Steel/TiC Composites

سال انتشار: 1389
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,739

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

COMPOSIT02_193

تاریخ نمایه سازی: 24 مهر 1389

چکیده مقاله:

This study deals with the processing, microstructure, and wear behavior of low volume fractions of TiC reinforced high chromium steel matrix composites. Composite processing was performed in a high frequency induction furnace while mechanical stirring assisted uniform dispersion of second phase particles into the molten steel. The in-situ melting of 70Cr2 steel and ferrotitanium (Fe-70%Ti) caused reaction between carbon and titanium which produced titanium carbide particles within the melt. Type and amount of matrix phases, shape, size, and distribution of the secondary phase were recognized by scanning electron microscopy (SEM), optical microscope (OM) equipped with image analyzer, micro hardness and quantometry. The density of the samples was measured by the Archimedes’s method and the wear behavior of the unreinforced 70Cr2 alloy and composite samples were investigated using a pin-on-disc test at room temperature under dry conditions.The result revealed that these composites can be produced successfully by this technique and low volume fractions of TiC particles are distributed uniformly in the steel matrix phase. Also it has been found that with the fabrication of low volume fraction of TiC particles in the high chromium steel matrix the hardness and wear resistance of the composite significantly increased.

کلیدواژه ها:

Fe-TiC composite ، In situ ، 70Cr2 steel ، Microstructure and Wear Behavior

نویسندگان

H Beygi

Master of Science

E Tohidlou

Faculty of Engineering, University of Sistan and Baluchestan, Daneshgah Street, Zahedan, Iran

M.R Rahimipour

Ceramic Department, Materials and Energy Research Centre, Tehran, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Hathaway, R.M., Rohatgi, P.K., Sobczak, N., and Sobczak, J. (1997), ...
  • Raghunath, C., Bhat, M. S., and Rohatgi P. K. (1994), ...
  • Pagounis, E., and Lindroos, V.K. (1998), Materials Science and Engineering ...
  • Das, K., B andyopadhyay, T. K., and Chatterjee, S. (2005), ...
  • Das, K., B andyopadhyay, T. K., and Das, S. (2002), ...
  • Razavi, M., Yaghmaee, M.S., Rahimipour, M.R., and Razavi Tousi, S.S. ...
  • Razavi, M., Rahimipour, M.R., and Rajabi-Zamani, A.H. (2007), Materials Science ...
  • Kattamis, T. Z., and Suganuma, T. (1990), Materials Science and ...
  • B andyopadhyay, T. K., And Das, K. (2004), Journal of ...
  • نمایش کامل مراجع