An experimental investigation on the effect of machining and MQL parameters on thesurface roughness in finish turning of Al۷۰۷۵ alloy
- سال انتشار: 1401
- محل انتشار: نوزدهمین همایش ملی و هشتمین کنفرانس بین المللی مهندسی ساخت و تولید ایران
- کد COI اختصاصی: ICME19_132
- زبان مقاله: انگلیسی
- تعداد مشاهده: 221
نویسندگان
M.Sc. Graduate, School of Mechanical Engineering, Iran University of Science and Technology
PHD, Associate Professor, School of Mechanical engineering, Iran University of Science and Technology
چکیده
Today, with increasing concerns about the harmful effects ofthe cutting fluids on the environment, many efforts have beenmade to reduce the consumption of these fluids. Oneproposed solution to reduce cutting fluid consumption inmachining processes is using the Minimum Quantity ofLubrication (MQL) method. This method improvesmachining conditions by atomizing the cutting fluid andspraying it on the tool surface. In this research the effect ofthe MQL and the machining parameters, including cuttingfluid’s flow rate, MQL nozzle’s air pressure, feed rate, andcutting speed on workpiece surface roughness in the turningprocess of aluminum alloy ۷۰۷۵, were investigated byemploying the Response Surface Method (RSM). Based onthe results of experimental tests, the lowest surface roughnessobtained using parameters of the fluid flow rate of ۲۷۵ ml/h,the pressure of ۳ bar, cutting speed of ۲۰۰ m/min, and feedrate of ۰.۰۸ mm/rev was measured as ۰.۴۳۸ microns.Evaluating the results showed that the feed rate has a directrelationship with the surface roughness, and as the feed rateincreases, the surface roughness also increases. The effect ofcutting fluid’s flow rate, air pressure, and cutting speed on theworkpiece surface roughness does not have a consistent trendand depends on the cutting parameters. Therefore, statisticalor experimental analysis methods can be utilized to achievethe optimal values of workpiece surface roughness.کلیدواژه ها
Minimum Quantity of Lubrication (MQL)Parameters, Machining Parameters, Turning Process ofAluminum Alloy ۷۰۷۵, Surface Roughnessمقالات مرتبط جدید
- A Fuzzy Gait Phase Detection for Rehabilitation of Hemiplegic Patients with a HipExoskeleton Robot
- استفاده از فناوری کنترل عددی در رسم و نقاشی دو بعدی با استفاده از نازل رنگ پاش
- طراحی ، ساخت و کالیبراسیون میکرو پمپ سرنگی برای کاربردهای میکروفلوئیدیک
- تاثیر چسبندگی بین لایه های قطعات ساخته شده با پرینتر سه بعدی در شبیه سازی شکست خستگی
- Jerk-limited spatial PH trajectory generation for high-speed robotics application
اطلاعات بیشتر در مورد COI
COI مخفف عبارت CIVILICA Object Identifier به معنی شناسه سیویلیکا برای اسناد است. COI کدی است که مطابق محل انتشار، به مقالات کنفرانسها و ژورنالهای داخل کشور به هنگام نمایه سازی بر روی پایگاه استنادی سیویلیکا اختصاص می یابد.
کد COI به مفهوم کد ملی اسناد نمایه شده در سیویلیکا است و کدی یکتا و ثابت است و به همین دلیل همواره قابلیت استناد و پیگیری دارد.