Surface Mechanical Coating of Fe Plate with Ni and Cu powders by Mechanical Alloying Method

سال انتشار: 1395
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 436

فایل این مقاله در 7 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

IMES10_564

تاریخ نمایه سازی: 6 اردیبهشت 1396

چکیده مقاله:

A new coating process is offered to produce a coating layer on Fe plate by the mechanical milling process. In this paper, the Cu and Ni were applied over a steel substrate in the room temperatureand under the environment atmosphere using the crushing balls in different milling times for samples (Ni-30% Cu) in order to make coat. Bilateral entrance of nickel and copper elements during milling causes Ni-Cu solid solution to be made and the composite coat to be created over the samples surface. The microstructure properties of coat surface by use of varied analyses such as: field emission scanning electron microscope (FESEM), energy dispersive X-ray spectroscopy, surface roughness and friction analyses showed that the coat layer thickness reach to 100 micrometres. X-ray diffraction results proved the solid solution formation of nanocrystals

کلیدواژه ها:

Mechanical milling ، Ni-Cu nanostructure solid solution ، FESEM ، Milling time

نویسندگان

Iman Farahbakhsh

Shirvan Center, University of Applied Science and Technology, Shirvan, Iran

Abbas Sabahi Namini

Department of Materials Engineering, Sahand University of Technology, Tabriz, Iran

Babak Mazinani

Department of Materials Engineering, Malayer University, Malayer, Iran.

Zohre Ahmadi

Department of Materials Science and Engineering, University of Tabriz, Tabriz, Iran.

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • بنجمین کنفرنس بین‌لمللی مهندسی‌مود ومتلویی ودهمین کنفرنس مشترک‌فجمن مهندسین _ ...
  • C. Koch, "Intermetallic matrix composites prepared by mechanical alloying-a review, ...
  • Suryanarayana, "Mechanical alloying and milling, " Progress in Materials Science, ...
  • M. S: E I-Eskandarany, Mechanical Alloying For Fabrication Of Advanced ...
  • W. P. Tong, N. R. Tao, Z. B. Wang, J. ...
  • Choudhary, R., et al., Structural and dielectric properties of mechano ...
  • , 9 Nov. 2016 Shiraz University ...
  • , 9 Nov. 2016 Shiraz University ...
  • Torosyan, A.T., L., Me chanochemical reaction at the interface between ...
  • Takacs, L. and A. Revesz, Preparation of Coatings by Mechanical ...
  • Tharamani, C. and S. Mayanna, Low-cost black Cu-Ni alloy coatings ...
  • Baskaran, I., T. Sankara Narayanan, and A. Stephen, Pulsed electrodepo ...
  • Waje, S.B., et al., X-ray diffraction studies on crystallite size ...
  • U. Erb, G. Palumbo, R. Zugic, and K. Aust, "Processing ...
  • , 9 Nov. 2016 Shiraz University ...
  • نمایش کامل مراجع