Lattice Boltzmann Simulation of Deformation and Breakup of a Droplet under Gravity Force Using Interparticle Potential Model

  • سال انتشار: 1392
  • محل انتشار: ماهنامه بین المللی مهندسی، دوره: 26، شماره: 7
  • کد COI اختصاصی: JR_IJE-26-7_005
  • زبان مقاله: انگلیسی
  • تعداد مشاهده: 836
دانلود فایل این مقاله

نویسندگان

s.e Mousavi Tilehboni

Faculty of Mechanical Engineering, Babol Noshirvani University of Technology, Postal Code ۴۷۱۴۸۷۱۱۶۷, Babol, Iran

k Sedighi

Faculty of Mechanical Engineering, Babol Noshirvani University of Technology, Postal Code ۴۷۱۴۸۷۱۱۶۷, Babol, Iran

m Farhadi

Faculty of Mechanical Engineering, Babol Noshirvani University of Technology, Postal Code ۴۷۱۴۸۷۱۱۶۷, Babol, Iran

e Fattahi

Faculty of Mechanical Engineering, Babol Noshirvani University of Technology, Postal Code ۴۷۱۴۸۷۱۱۶۷, Babol, Iran

چکیده

In this paper interparticle potential model of the lattice Boltzmann method (LBM) is used to simulate the deformation and breakup of a falling droplet under the gravity force. First, this model is applied to ensurethat the surface tension effect is properly implemented in this model. Two tests have been considered.First, it has been checked an initial square drop in a 2D domain can freely deform to a circular drop and secondly the coalescence of two static drops that merge to become a single circular drop is simulated. In order to further verify the model, Laplace law for static drops is performed. In the next step, wall effectson the droplet shape and its average velocity have been studied. It is seen that the average velocity ofdroplet at different times is independent of wall effects when the ratio of the width of the channel to droplet diameter (W/D) is more than 6. In the final section of the paper, deformation and breakup of a falling droplet for some range of Eotvos and Ohnesorge numbers are investigated. It is seen that at verylow Eotvos numbers, where the surface tension force is dominant, the droplet deforms slowly and reaches a steady state without breakup. At higher Eotvos numbers gravitational force overcome the surface tension force and the droplet deforms more. For breakup modes at the small Ohnesorge number, if Eotvos numberbe increased to an intermediate value, the droplet deforms more than from a state of low Eotvos numbervalue and eventually forms a backward-facing bag. Finally, for high Eotvos numbers, fragments of droplet are sheared from the edges and the shear breakup mechanism is seen. On the other hand, the stabilizing effect of the Ohnesorge number, (the ratio of viscous stresses and surface tension) is shown. At higher Ohnesorge number, the simulations show that the main effect of increasing Ohnesorge number is to move the boundary between the different breakup modes to higher Eotvos number

کلیدواژه ها

Falling droplet,Breakup,Lattice Boltzmann method,Interparticle potential model,Eotvos number

مقالات مرتبط جدید

اطلاعات بیشتر در مورد COI

COI مخفف عبارت CIVILICA Object Identifier به معنی شناسه سیویلیکا برای اسناد است. COI کدی است که مطابق محل انتشار، به مقالات کنفرانسها و ژورنالهای داخل کشور به هنگام نمایه سازی بر روی پایگاه استنادی سیویلیکا اختصاص می یابد.

کد COI به مفهوم کد ملی اسناد نمایه شده در سیویلیکا است و کدی یکتا و ثابت است و به همین دلیل همواره قابلیت استناد و پیگیری دارد.