Study on Effective Factors on Deposition of Nanostructure Electroless Ni-Cu-P Coating on ST Steel

سال انتشار: 1387
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,138

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICNN02_530

تاریخ نمایه سازی: 27 شهریور 1391

چکیده مقاله:

Electroless Ni-based coatings are special interest due to their properties such as good corrosion and wear resistance, deposited uniformity, electrical and thermal conductivity. These are widely used in chemical, aerospace, automobile and textile industries. The quality of coatings is dependent upon the microstructure and composition of the deposits. Electroless process for nickel coatings produces deposits having microcrystalline, amorphous or fully crystalline nature over a wide range of compositions [ ]. In general, Electroless Nickel deposits are classified into three categories: low ( wt. %), medium ( wt. %) and high ( wt. % and above) phosphorus deposits. Studies have shown that as-coated low-phosphorus deposits are either crystalline or consist of microcrystalline nickel. As-coated medium-phosphorus deposits are reported to be either fully amorphous or mixtures of microcrystalline nickel and amorphous phases. Studies on high-phosphorus as-coated deposits have demonstrated that the deposits could be fully amorphous, mixtures of microcrystalline nickel and amorphous. [ ]The crystallite size of the coatings determines the quality of coatings. The crystallite size may be influencing the Peak broadening in the coatings [ ]. In this paper, the effect of pH, sodium hypophosphite, copper sulphate and sodium sitrate concentration on microstructure of Ni-Cu-P coatings were investigated

نویسندگان

F Soleimangoli

Material Engineering Faculty.Sahand

R Azari-Khosroshahi

Material Engineering Faculty.Sahand University,Tabriz.Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • J.T.Winowlin Jappes, B _ Ramamoorthy , P. Kesavan Nair, jornal ...
  • K.G.Keong, W.Sha, S .Malinov.jornal of Alloys and Compounds33 4(2 _ ...
  • .N. Balaraiu, K.S. Rajam, Surface Engineering Division, 2 _ _ ...
  • نمایش کامل مراجع