Investigation of Reinforcing Effects of Clay on In-situ polymerized Polypropylene/Clay Nanocomposites using Bi-Supported Ziegler-Natta Catalyst

سال انتشار: 1387
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 903

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICNN02_350

تاریخ نمایه سازی: 27 شهریور 1391

چکیده مقاله:

Polymer/clay nanocomposites are the subject of intense research efforts in recent years. Polypropylene (PP), as one of the general plastics, when filled with nanoclay or nanoparticles can be one of the suitable choice substitute for high performance engineering plastic. Melt blending [1–3], solution blending [4-5], and in situ polymerization [6–9] methods have been used to prepare PP/clay nanocomposites. However it is not an easy task to prepare exfoliated PP/clay nanocomposites with the first two methods, due to the incompatibility of hydrophobic PP and hydrophilic clay. Therefore, in situ polymerization is most effective method to prepare exfoliated PP/clay nanocomposites compared with melt and solution blending methods [10].Ziegler-Natta catalysts are mostly used for industrial production of olefinic polymer such as isotactic polypropylene and high density and linear low-density polyethylene [11].In this work, bi-supported Ziegler-Natta catalyst of TiCl4/MgCl2 (ethoxide type)/clay was used to prepare PP/clay nanocomposites. The morphology, thermal and mechanical properties of prepared nanocomposites, were investigated in this research and compared with those of samples that obtained from melt blending. The thermo-mechanical properties of prepared samples were considerably improved at rather low content of clay in polymeric matrix

نویسندگان

S.A Ramazani

Chemical and Petroleum Engineering Department, Sharif University of Technology, P.O. Box: ۱۱۳۶۵-Tehran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • M. Kawasumi, N. Hasegawa, M .Kato, M acromolecue S _ ...
  • N. Hasegawa, M. Kawasumi, M. Kato, J Appl Polym Sci, ...
  • PH. Nam, P. Maiti, M. Okamoto, Polymer, 42, 9633-9640, _ ...
  • Y. Kurokawa, H. Yasuda, A. Oya, J Mater Sci Lett, ...
  • A Oya, Y Kurokawa, H Yasuda, J Mater Sci, 35, ...
  • T .Sun, JM. Garces, Adv Mater, 14, 128-30, 2002 ...
  • T. Nishiwaki. JP09118792, Chem Abstr, 127, 51586, 1997 ...
  • J. Tudor, L Willington D, O Hare, Chem Commun, 2031-2032, ...
  • J.Tudor, D. O Hare. Chem Commun, 603-4, 1997 ...
  • M .Zanetti, G. Camino, P. Reichert, R. Mulhaupt, Macromol Rapid ...
  • A. Siokou, S. Ntais, Surface Science, 540, 379-388, 2003 ...
  • A.Ramazani S.A, H.Baniasadi, F.Tavakolzade, Characte rization of po ly e ...
  • نمایش کامل مراجع