Study on Manufacturing of Internal Gear by Flowforming Process and Investigation of Effective Parameters on Process Force

سال انتشار: 1400
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 308

فایل این مقاله در 12 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_IJMF-8-1_003

تاریخ نمایه سازی: 18 فروردین 1400

چکیده مقاله:

Flowforming is a plastic deformation process that is used to produce precise thin-walled tubes. Manufacturing of an internal gear through flowforming process is a new method by which the gear can be manufactured in just one pass. In the present study, the flowforming of internal gear is studied both experimentally and numerically. A simple set up was designed and built to manufacture the internal gear. The plastic behavior of the material was determined through tensile testing, and the friction condition was determined using a friction test. Parameters including profile and teeth height were measured and compared with simulated values. It is shown that there is a good agreement between the results of the simulation and those of the experiment. When the simulation is verified, the design of the experiment method is employed to investigate the influences of roller diameter, feed rate, thickness reduction percentage and attack angle on the process force. According to DOE results, all parameters and interactions are significant and affect the process force except D×T. The process force increases by increasing the roller diameter, thickness reduction percentage and feed rate, but decreases by increasing the attack angle.

نویسندگان

Majid Khodadadi

Department of Mechanical Engineering, University of Birjand, Birjand, Iran

Khalil Khalili

Department of Mechanical Engineering, University of Birjand, Birjand, Iran

Amir Ashrafi

Department of Mechanical Engineering, University of Birjand, Birjand, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • [1] M. Merklein, J.M. Allwood, B.A. Behrens, A. Brosius, H. ...
  • [2] C. C. Wong, T. A. Dean, and J. Lin, ...
  • 1419-1435. ...
  • [3] H. Nägele, H. Wörner, and M. Hirschvogel, Automotive parts ...
  • [4] P. Groche and D. Fritsche, Application and modelling of ...
  • [5] S.Y. Jiang, Z.Y. Ren, W. Bin, and G.X. Wu, ...
  • [6] S. Jiang, Z. Ren, K. Xue, and C. Li, ...
  • [7] S.Y. Jiang, Y.F. Zheng, Z.Y. Ren, and C.F. Li, ...
  • [8] S. Jiang, Z. Ren, C. Li, and K. Xue, ...
  • [9] M. Haghshenas, M. Jhaver, R. Klassen, and J. Wood, ...
  • [10] M. Haghshenas, J. Wood, and R. Klassen, Investigation of ...
  • [11] M. Haghshenas, J. Wood, and R. Klassen, Effect of ...
  • [12] Q.-X. Xia, L.-Y. Sun, X.-q. Cheng, and B.-Y. Ye, ...
  • [13] W. Xu, X. Zhao, D. Shan, J. Li, Q. ...
  • [14] M. A. Rasouli, A. Taherizadeh, M. Farzin, A. Abdolah, ...
  • [15] M. Movahhedy, M. Gadala, and Y. Altintas, Simulation of ...
  • [16] D. C. Montgomery, Design and analysis of experiments. John ...
  • [17] C. Wong, T. Dean, and J. Lin, Incremental forming ...
  • [18] Y. Jianguo and M. Makoto, An experimental study on ...
  • نمایش کامل مراجع