Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets

سال انتشار: 1399
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 199

فایل این مقاله در 7 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_ADMTL-13-3_005

تاریخ نمایه سازی: 16 دی 1399

چکیده مقاله:

In recent decades, the use of aluminium alloys is developed in the automotive industry with regard to the need for lightweight and anti-corrosion components, one of which is AA7075 Al alloy. In this study, the multi-step deep drawing process of AA7075 aluminium sheets under various blank holder forces is investigated through a numerical simulation and is then validated with experimental results. Simulations were conducted by ABAQUS finite element software, and the influences of the blank holder force on the wrinkling height, rupture occurrence and thickness distribution of the sheet were studied. The optimum amount of blank holder force at each drawing step is determined so that the height of wrinkling, and the thinning percentage do not exceed the permissible value. Based on the results, the blank holder force magnitude should be considered descending during the four successive steps to achieve more uniform thickness distribution, and also the wrinkling height could be reduced by increasing the blank holder force in the analysed force range. The optimum amount of blank holder force in the four drawing steps was 28000, 2500, 1500 and 600 N, respectively. In general, the minimum thickness was created in the corner of the punch. The results also showed that an excessive increase in the blank holder force in order to eliminate the wrinkling caused the thinning percentage to increase. Finally, a good accordance between the experimental and numerical results was observed.

نویسندگان

Sajad Bakhtiari

Department of Mechanical Engineering, Shahid Rajaee Teacher Training University, Tehran, Iran

Seyed Jalal Hashemi

Department of Mechanical Engineering, Faculty of Enghelab-e Eslami, Tehran Branch, Technical and Vocational University (TVU), Tehran, Iran

Amir Hossein Roohi

Department of Mechanical Engineering, Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University, Qazvin, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • [1]     Koc, M., Altan, T., An Overall Review of the ...
  • [2]     Colgan, M., Monaghan, J., Deep Drawing Process: Analysis and ...
  • [3]     Vollertsen, F., Prange, T., and Sander, M., Hydroforming: Needs, ...
  • [4]     Hashemi, S. J., Naeini, H. M., Liaghat, G., Karami, ...
  • [5]     Choi, T., Choi, S., Na, K., and Bae, H., ...
  • [6]     Sheng, Z., Taylor, R., and Strazzanti, M., FEM-Based Progressive ...
  • [7]     Li, W., Meng, B., Wang, C., Wan, M., and ...
  • [8]     Sivasankaran, S., Narayanasamy, R., Jeyapaul, R., and Loganathan, C., ...
  • [9]     Tikhovskiy, I., Raabe, D., and Roters, F., Simulation of ...
  • [10]  Liu, W., Chen, B. K., Sheet Metal Anisotropy and ...
  • [11]  Qayyum, F., Shah, M., Muqeet, A., and Afzal, J., ...
  • [12]  Proubet, J., Baudelet, B., Rupture Criteria During Deep Drawing ...
  • [13]  Zhang, W., Tor, S., and Britton, G., Indexing and ...
  • [14]  Abdelmaguid, T. F., Abdel-Magied, R. K., Shazly, M., and ...
  • [15]  Pacheco, M., Celentano, D., García-Herrera, C., Méndez, J., and ...
  • [16]  Brown, W. F., Mindlin, H., and Ho, C. Y., ...
  • [17]  Sheng, Z., Jirathearanat, S., and Altan, T., Adaptive FEM ...
  • نمایش کامل مراجع