Ultrasonic guided waves reflection from simple dent in pipe for defect rate estimation and parameters determination of axisymmetric wave generation source

سال انتشار: 1399
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 288

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_JCAM-51-1_007

تاریخ نمایه سازی: 31 تیر 1399

چکیده مقاله:

In this paper, the reflection of ultrasonic guided waves from simple dent in pipes has been investigated using finite element method and the relationship between reflection coefficient of these waves and deformation rate has been determined. Also, the effect of the parameters of wave generation source on the generated wave field has been investigated using normal modes expansion method. At first, ultrasonic guided waves propagation has been studied in an intact pipe to obtain multiple modes using of displacement potential method. The characteristic equation has been solved using a matlab code in order to draw the dispersion curves of phase and group velocities in different frequencies for longitudinal modes, and it is observed that mode L(0,2) is a suitable mode for inspection in a range of frequency 200-300 kHz. The single sided dent is created in pipe using a plasticity analysis with the aid of finite element simulation and then L(0,2) mode is generated in pipe. By Investigation of the reflection of this mode from dent, the relationship between reflection coefficient and deformation rate is specified and it has been observed that this relationship is almost linear by curve fitting. Also, it has been observed in case of partial loading by wave generation source that is a transducer with a specified axial length and circumferential coverage angle, a combination of different modes such as L(0,2) mode is generated in pipe, if using a axisymmetric wave generation source including 8 segments 45 degree, only L(0,2) symmetric mode is generated.

نویسندگان

Pezhman Taghipour birgani

Department of Mechanical Engineering, Ahvaz Branch, Islamic Azad University, Ahvaz, Iran.

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • D. N. Alleyne, P. Cawley, The effect of discontinuities on ...
  • D. N. Alleyne, M. J. S. Lowe, P. Cawley, The ...
  • M. J. S. Lowe, D. N. Alleyne, P. Cawley, The ...
  • D. N. Alleyne, B. Pavlakovic, M. J. S. Lowe, P. ...
  • K. A. Macdonald, A. Cosham, C. R. Alexander, P. Hopkins, ...
  • W. B. Na, T. Kundu, Underwater pipeline inspection using guided ...
  • J. L. Rose, 2014, Ultrasonic guided waves in solid media, ...
  • S. Ma, Z. Wu, Y. Wang, K. Liu, The reflection ...
  • F. P. Baaijens, W. R. Trickey, T. A. Laursen, F. ...
  • M. Dao, C. T. Lim, S. Suresh, Mechanics of the ...
  • D. N. Alleyne, P. Cawley, Optimization of Lamb wave inspection ...
  • M. J. S. Lowe, D. N. Alleyne, P. Cawley, Defect ...
  • J. Mu, Guided wave propagation and focusing in viscoelastic multilayered ...
  • P. T. Birgani, K. N. Tahan, S. Sodagar, M. Shishesaz, ...
  • Vol. 15, No. 3, pp. 63-74, 2015. ...
  • J. J. Ditri, J. L. Rose, Excitation of guided elastic ...
  • J. J. Ditri, J. L. Rose, Excitation of guided waves ...
  • J. Achenbach, 1984, Wave propagation in elastic solids, North Holland, ...
  • نمایش کامل مراجع